![referance g code for sheetcam mach 3 referance g code for sheetcam mach 3](http://www.helmancnc.com/wp-content/uploads/2014/01/Mach3-m-code-helmancnc.com_.jpg)
- #REFERANCE G CODE FOR SHEETCAM MACH 3 HOW TO#
- #REFERANCE G CODE FOR SHEETCAM MACH 3 INSTALL#
- #REFERANCE G CODE FOR SHEETCAM MACH 3 32 BIT#
All setting regarding THC we can do it in PlugIn control -> Configure PoKeys57CNC -> Pulse engine settings tab.Ĭhoose PlasmaSens in THC setting -axis Z section group.To use a split 10V input, you must select the Easy Sensor (ID) number that corresponds to the PlasmaSens 10 V input. 50:1 ratio will be perfect for PlasmaSens 10V input (pin-3 and pin-4).Ĭlick to enlarge: connection to HV or divided outputĬonnect optical interface flat cable with red micro-match connector to PoKeys57CNC (PoExtension2). The second way is using an divided voltage that some plasmas manufacturer have factory installed. Watch for polarity! A cutter’s clamp is positive voltage potential and it goes to pin1. You should use a HV input terminal pin1 and pin6. Make sure you use a double isolated short wire for voltage detection. In that case you will probably need to do some adaptation on the cutter itself as usually doesn’t have such an output. The first is connecting directly to cutters output. When you insert the cable, you will feel a click. Make sure you remove plastic caps at optical transmitter/receiver and protection caps on the optical cable. Connect AC power supply (110 VAC-230 VAC/50-60 Hz) and apply optical cable to PlasmaSens and optical interface. PlasmaSensįirst we have to power up PlasmaSens and establish communication with PoKeys57CNC. In this article we will focus on a THC setup options and we will assume that we already set the axis, motor parameters and limit switches.
#REFERANCE G CODE FOR SHEETCAM MACH 3 INSTALL#
It is always a good idea to install the latest application and plugin version! To be sure, you can check if PoKeys.dll exists in C:\Mach3\PlugIns folder. The PoKeys Mach3 plugin will be automatically installed along with the app. The next thing if you are going to use PlasmaSens with a PK57CNC controller is to download the PoKeys configuration package and run the installation.
#REFERANCE G CODE FOR SHEETCAM MACH 3 HOW TO#
I also advise you to browse on a YouTube how to start with Mach3. If you will working with Mach3 for the first time here is a link where to download it: Mach3 download page.
![referance g code for sheetcam mach 3 referance g code for sheetcam mach 3](https://www.montresetvous.com/10736-medium_default/lip-mach-2000-mini.jpg)
![referance g code for sheetcam mach 3 referance g code for sheetcam mach 3](https://www.avidcnc.com/support/instructions/software/img/Mach4_FileOps.jpg)
Description for PlasmaSensOut can be used to setup any other generic CNC controller board. PlasmaSensOut namely generates universal THC control signals Arc_OK, Torch_Up and Torch_Down.įirst we will describe the case with PlasmaSens and PK57CNC. While on the other hand PlasmaSensOut comes with the user friendly HMI device and can be connected with any other CNC controller board.
![referance g code for sheetcam mach 3 referance g code for sheetcam mach 3](https://img.yumpu.com/6671406/1/500x640/setup-and-operation-manual-sheetcam.jpg)
However, PlasmaSens comes with optical interface and is meant to be used with CNC controller board PK57CNC. The last one is suitable for cutters with internal voltage divider output. High voltage input up to 350 VDC or low voltage input up to 10 VDC. Moreover device offers two arc voltage level inputs.
#REFERANCE G CODE FOR SHEETCAM MACH 3 32 BIT#
PlasmaSens and PlasmaSensOut are design on modern 32 bit microprocessor’s voltage measurement technology. Let’s get to the point! How to use plasma with Mach3? Mach3 plasma setup quick guideįirst let me briefly introduce our two product from torch control PlasmaSens series and the difference between them. This article will guide you through the process of setting THC with your CNC controller board and Mach3. Here is a quick guide how to easy perform Mach3 plasma setup.